BoPin 550 Mould-Resistant Sanitary Silicone Sealant

BoPin 550 is a single-component, neutral-cure, medium-modulus silicone sealant specifically formulated for kitchen and bathroom sealing applications. It incorporates a high-molecular-weight modified base material and a proprietary long-lasting anti-mould formula that provides sustained protection against mould and bacterial growth in permanently wet and humid environments. The non-corrosive cure chemistry makes it safe for use on coated glass, ceramic, marble, granite and metal fixtures without risk of staining or surface damage. Suitable for both interior and exterior applications, it requires no primer on most common sanitary substrates and delivers durable, watertight seals that maintain their integrity and appearance over extended periods in wet areas.

Temel Faydalar

Long-lasting anti-mould and anti-bacterial protection — specially formulated for permanently humid sanitary environments
Neutral cure — non-corrosive to metals, coated glass, ceramics, marble and granite
Excellent weather resistance — resists UV radiation and temperature cycling
Good adhesion to most common sanitary substrates without primer
Non-sag formula — maintains position on vertical joints around baths, basins and shower enclosures
Waterproof seal — prevents water ingress at joints between sanitary fixtures and surrounding surfaces
Suitable for both indoor and outdoor wet-area applications

Adhere To

Seramik ve porselen karolar
Vitreous enamel and acrylic sanitary ware
Marble and granite
Glass and coated glass
Stainless steel, chrome and aluminium fixtures
Beton ve duvarcılık

Application Areas

Sealing around bathtubs, shower trays and shower enclosures
Basin and sink to wall and worktop joint sealing
Toilet base and cistern sealing
Kitchen worktop and splashback joint sealing
Ceramic tile joint sealing in wet areas
General indoor and outdoor decorative waterproof sealing

Paket

300ml cartridge — 24 units per carton
Available colors upon request

Ek bilgi

Temel Malzeme	Nötr oksim silikon
Kürleme Sistemi	Neutral cure (medium modulus)
Yoğunluk	1,01 g/cm³
Sertlik (Shore A)	20±5
Kopma Uzaması	>500%
Hareket Kabiliyeti	±25%
Sıcaklık Dayanımı	-40°C ila +120°C
Uygulama Sıcaklığı	+5°C ila +40°C
Deri Oluşum Süresi	10-20 dakika (23°C/50% bağıl nem)
Kürlenme Süresi	2-3mm/24 saat (23°C/50% bağıl nem)
VOC İçeriği	<35 g/L
Sıhhi Sınıf	XS1 (en yüksek sıhhi sınıf)
Renk	Siyah, Şeffaf, Özelleştirilmiş, Gri, Beyaz
Standard	JC/T 885-2016

Yüzey Hazırlığı — Remove all old sealant, soap residue, grease and moisture from surfaces. Surfaces must be completely dry before application — allow at least 24 hours after last water contact.
Uygulama — Cut cartridge tip at 45°, load into sealant gun and apply with steady, even pressure. Tool immediately using a wet spatula or sealant finishing tool for a smooth, concave finish.
Curing — Allow to cure at room temperature with adequate ventilation. Avoid water contact for at least 24 hours after application. Full mechanical properties and mould resistance develop after 7 days.
Temizlemek — Remove uncured sealant with a solvent. Cured sealant must be removed mechanically.

Limitations

Not suitable for structural load-bearing applications
Not suitable for continuous full water immersion
Not suitable for use in fully enclosed, unventilated spaces
Not suitable for surfaces containing plasticiser or solvent residues
Keep away from children
Do not apply when substrate temperature is below 5°C or above 40°C

İpuçları

Thorough surface preparation is the single most important factor in achieving a long-lasting, mould-free seal — any moisture, soap residue or old sealant will shorten joint life
Apply masking tape along both sides of the joint before application for clean, professional lines — remove immediately after tooling before skin forms
In high-humidity climates (tropical, subtropical), ensure adequate bathroom ventilation after installation to extend mould-free service life
Store cartridges upright in a cool, dry location away from heat and direct sunlight