BoPin 110 All-Purpose Acetoxy Silicone_Applications

BoPin 110 All-Purpose Acetoxy Silicone_Benefits

BoPin 110 Çok Amaçlı Asetoksi Silikon Mastik

BoPin 110, genel cam ve sızdırmazlık uygulamaları için tasarlanmış tek bileşenli, asetoksi kürlemeli silikon mastiktir. Neme maruz kaldığında oda sıcaklığında hızla kürleşerek, geniş bir sıcaklık aralığında performansını koruyan dayanıklı, esnek bir kauçuk oluşturur. Hızlı yüzey oluşumu ve cam ve seramik yüzeylere güçlü yapışması, pencere montajı, dekoratif cam yapıştırma ve profesyonel boşluk doldurma için güvenilir bir seçim olmasını sağlar.

Temel Faydalar

Fast cure — tack-free within 8 minutes, significantly faster than neutral-cure alternatives
Strong adhesion to glass, glazed ceramics, and anodised aluminium without primer
Excellent elongation (≥400%) providing good flexibility under movement
UV resistant — resists ageing, yellowing and degradation from solar exposure
Stable performance from -50°C to +170°C
Non-sag formula suitable for vertical and overhead joints

Adhere To

Cam ve camlı yüzeyler
Anodised aluminium
Glazed ceramic tiles
Non-oily timber

Application Areas

Window and door frame installation and sealing
Decorative glass panel bonding and sealing
General-purpose gap filling by professional applicators
Aluminium window and door frames to wall joint sealing
Glass display cabinets and shopfront glazing

Paket

300ml cartridge — 24 units per carton
Available colors upon request

Ek bilgi

Temel Malzeme	Asetoksi silikon
Kürleme Sistemi	Acetoxy (acid cure)
Sag / Slump	≤3 mm
Deri Oluşum Süresi	≤8 min
Working Time	≤10 min
Cure Rate (depth)	1–2 mm/day
Sertlik (Shore A)	20
Çekme Dayanımı	≥1.0 MPa
Kopma Uzaması	≥400%
Hareket Kabiliyeti	±15%
Sıcaklık Dayanımı	-50°C to +170°C
Renk	Siyah, Kahverengi, Şeffaf, Özelleştirilmiş, Gri, Beyaz
Raf Ömrü	12 months (unopened, ≤25°C)
Standard	JC/T 485-2007

Yüzey Hazırlığı — Ensure all surfaces are clean, dry and free from dust, grease and old sealant residues.
Uygulama — Cut cartridge tip at 45°, load into sealant gun and apply with steady, even pressure. Tool within the working time using a wet spatula.
Curing — Allow to cure at room temperature. Avoid water contact for at least 24 hours. Full mechanical properties are reached after 7 days.
Temizlemek — Remove uncured sealant with a solvent. Cured sealant must be cut away mechanically.

Limitations

Not suitable for structural load-bearing applications
Not recommended for movement exceeding ±15%
Sürekli suya daldırma için önerilmez
Do not use in fully enclosed spaces without ventilation — releases acetic acid (vinegar odour) during cure
Do not apply directly to mirror reflective coatings — acid may damage the backing
Do not use on natural stone (marble, limestone, travertine) — acid may cause staining
Do not use on copper, brass, zinc or other acid-sensitive metals — corrosion may occur
Do not use on surfaces containing plasticiser or solvent residues
Do not apply when substrate temperature is below 4°C or above 40°C

İpuçları

For best tooling results, use a small amount of soapy water on the spatula to achieve a smooth finish
Always conduct a compatibility test on actual project materials before full application
Store upright in a cool, dry place away from direct sunlight