BoPin 110 All-Purpose Acetoxy Silicone_Applications

BoPin 110 All-Purpose Acetoxy Silicone_Benefits

Keo dán silicone Acetoxy đa năng BoPin 110

BoPin 110 is a single-component, acetoxy-cure silicone sealant designed for general glazing and sealing applications. It cures rapidly at room temperature upon exposure to moisture, forming a durable, flexible rubber that maintains performance across a wide temperature range. Fast skin formation and strong adhesion to glass and ceramic surfaces make it a reliable choice for window installation, decorative glass bonding, and professional gap filling.

Lợi ích chính

Fast cure — tack-free within 8 minutes, significantly faster than neutral-cure alternatives
Strong adhesion to glass, glazed ceramics, and anodised aluminium without primer
Excellent elongation (≥400%) providing good flexibility under movement
UV resistant — resists ageing, yellowing and degradation from solar exposure
Stable performance from -50°C to +170°C
Non-sag formula suitable for vertical and overhead joints

Adhere To

Kính và bề mặt tráng men
Anodised aluminium
Glazed ceramic tiles
Non-oily timber

Application Areas

Window and door frame installation and sealing
Decorative glass panel bonding and sealing
General-purpose gap filling by professional applicators
Aluminium window and door frames to wall joint sealing
Glass display cabinets and shopfront glazing

Bưu kiện

300ml cartridge — 24 units per carton Available colors upon request

Thông tin bổ sung

Vật liệu cơ bản	Acetoxy silicon
Hệ thống bảo dưỡng	Acetoxy (acid cure)
Sag / Slump	≤3 mm
Thời gian hình thành da	≤8 min
Working Time	≤10 min
Cure Rate (depth)	1–2 mm/day
Độ cứng (Shore A)	20
Độ bền kéo	≥1.0 MPa
Độ giãn dài khi đứt	≥400%
Khả năng di chuyển	±15%
Khả năng chịu nhiệt	-50°C to +170°C
Màu sắc	Đen, Nâu, Trong suốt, Tùy chỉnh, Xám, Trắng
Hạn sử dụng	12 months (unopened, ≤25°C)
Standard	JC/T 485-2007

Chuẩn bị bề mặt — Ensure all surfaces are clean, dry and free from dust, grease and old sealant residues.
Ứng dụng — Cut cartridge tip at 45°, load into sealant gun and apply with steady, even pressure. Tool within the working time using a wet spatula.
Curing — Allow to cure at room temperature. Avoid water contact for at least 24 hours. Full mechanical properties are reached after 7 days.
Cleanup — Remove uncured sealant with a solvent. Cured sealant must be cut away mechanically.

Limitations

Not suitable for structural load-bearing applications
Not recommended for movement exceeding ±15%
Không khuyến khích ngâm nước liên tục
Do not use in fully enclosed spaces without ventilation — releases acetic acid (vinegar odour) during cure
Do not apply directly to mirror reflective coatings — acid may damage the backing
Do not use on natural stone (marble, limestone, travertine) — acid may cause staining
Do not use on copper, brass, zinc or other acid-sensitive metals — corrosion may occur
Do not use on surfaces containing plasticiser or solvent residues
Do not apply when substrate temperature is below 4°C or above 40°C

Mẹo

For best tooling results, use a small amount of soapy water on the spatula to achieve a smooth finish
Always conduct a compatibility test on actual project materials before full application
Store upright in a cool, dry place away from direct sunlight

Keo dán silicone Acetoxy đa năng BoPin 110

Thông tin bổ sung

Similar and Related Products

Sản phẩm tương tự

Keo dán silicone đá tự nhiên BoPin 635

Keo dán cửa sổ và cửa ra vào bằng silicon BoPin 220

Keo silicone chịu nhiệt độ cao BoPin 770

Keo dán silicone trung tính vệ sinh BoPin 550