BoPin 820 Multi-Purpose Construction Adhesive

BoPin 820 Multi-Purpose Construction Adhesive

BoPin 820 is a single-component, moisture-curing MS polymer adhesive and sealant formulated for general construction bonding and sealing applications across a wide range of substrates. Based on modified silane polymer technology, it cures at room temperature to form a strong, flexible rubber with excellent adhesion to concrete, glass, aluminium, stainless steel, aluminium composite panel, ceramic and timber — typically without primer. The medium-hardness cured body provides a good balance of bond strength and flexibility suitable for general construction joints, panel installation and bonding applications where a versatile, paintable, solvent-free adhesive is required.

Lợi ích chính

Excellent adhesion to a wide range of substrates including concrete, glass, aluminium, stainless steel, ACP, ceramic and timber — typically without primer
Paintable after cure — compatible with most water-based and solvent-based paint systems
Solvent-free, low-odour formula — suitable for use in occupied interior and exterior spaces
Good elongation (220%) — provides flexibility to accommodate minor joint movement
No shrinkage during cure
Suitable for both interior and exterior applications
Shelf life 12 months

Adhere To

Bê tông và xây nề
Glass and coated glass
Aluminium and aluminium alloy profiles
Stainless steel
Aluminium composite panels (ACP)
Gốm sứ
Timber and wood-based panels

Application Areas

General construction gap and joint sealing across a wide range of substrates
Aluminium composite panel (ACP) installation and joint sealing
Interior fit-out bonding and sealing applications
Automotive body and rail vehicle body high-strength joint sealing
Elevator cab assembly and sealing

Bưu kiện

300ml cartridge — 24 units per carton
600ml sausage pack — 20 units per carton
Available colors upon request

Thông tin bổ sung

Hệ thống bảo dưỡng	MS Polymer (moisture cure)
Density (g/cm³)	1.58
Độ cứng (Shore A)	55
Tensile Strength (MPa)	1.56
Elongation at Break (%)	220
Skin Formation Time (min)	16
Cure Rate (depth, mm/24h)	2.0
Extrudability (g/5s)	75
Aluminium Bonding	Pass
Glass Bonding	Pass
Hạn sử dụng	12 months (unopened, ≤27°C)
Màu sắc	Đen, Tùy chỉnh, Xám, Trắng

Chuẩn bị bề mặt — Ensure all surfaces are clean, dry and free from dust, grease and loose material. For best results on smooth non-porous surfaces such as glass and polished metal, wipe with isopropyl alcohol and allow to dry before application.
Ứng dụng — Cut cartridge tip at 45°, load into sealant gun and apply with steady, even pressure. For bonding applications, apply in parallel beads or a serpentine pattern to the bonding surface. Press components together firmly within the skin formation time.
Curing — Allow to cure at room temperature with adequate ventilation. Avoid disturbing bonded components for at least 24 hours. Full mechanical properties develop after 7 days.
Cleanup — Remove uncured product with a suitable solvent before skin formation. Cured product must be removed mechanically.

Limitations

Not suitable for PE, PP or PTFE surfaces
Không thích hợp để ngâm nước liên tục
Không phù hợp cho các ứng dụng kính kết cấu
Not suitable for surfaces containing plasticiser or solvent residues
Do not apply when substrate temperature is below 4°C or above 40°C

Mẹo

The medium hardness (Shore A 55) and good elongation (220%) make this product well suited for general construction bonding and sealing — for high-strength structural panel bonding where tensile strength above 3.0 MPa is required, consider BoPin 850
For ACP panel installation, apply adhesive beads at regular intervals across the panel back — bead spacing and pattern should be determined by panel size and wind load requirements
Paintability is a key advantage — allow full cure before applying paint for best adhesion results
Store cartridges upright in a cool, dry location away from heat and direct sunlight