Всепогодный строительный силиконовый герметик BoPin 150

BoPin 150 All-Weather Construction Silicone Sealant_applications

BoPin 150 All-Weather Construction Silicone Sealant_benefits

Всепогодный строительный силиконовый герметик BoPin 150

BoPin 150 is a single-component, neutral-cure oxime silicone sealant formulated for general construction sealing applications requiring reliable weatherproofing performance. It cures at room temperature upon exposure to atmospheric moisture, forming a durable, flexible rubber with good resistance to UV radiation, ageing and extreme temperature variations. The non-sag formula and broad substrate compatibility make it a dependable choice for both interior and exterior construction sealing where conditions are more demanding than standard gap filling.

Основные преимущества

Neutral cure — non-corrosive, safe for use on metals and powder-coated surfaces
Good movement capability (±20%) — handles more joint movement than standard neutral silicones
Non-sag formula — maintains position on vertical and overhead joints without slumping
UV resistant — resists ageing, yellowing and degradation from prolonged solar exposure
Good adhesion to most common building substrates without primer
Stable performance from -50°C to +170°C
Widely compatible with metals, glass, coated surfaces, masonry and timber

Придерживаться

Glass and coated glass
Aluminium and powder-coated metals
Ceramic and glazed tiles
Brick, concrete and masonry
Non-oily timber

Области применения

Window and door frame sealing and perimeter joint filling
Metal and aluminium alloy door and window frame to wall joint sealing
Glass, coated glass, ceramic tile, brick and concrete joint sealing
Small appliance assembly bonding and sealing
General exterior and interior construction joint sealing

Пакет

Картридж 300 мл — 24 единицы в упаковке
Упаковка колбасок 600 мл — 20 штук в коробке.
Доступные цвета по запросу.

Детали

Система полимеризации	Neutral (oxime cure)
Провисание / Спад	≤3 мм
Время формирования кожи	≤30 min
Рабочее время	≤20 мин
Степень полимеризации (глубина)	1–2 mm/day
Цвет	Индивидуальный
Твердость (по Шору A)	40
Прочность на разрыв	≥1,0 МПа
Удлинение при разрыве	≥200%
Возможность перемещения	±20%
Температурная стойкость	-50°C to +170°C
Срок годности	12 months (unopened, ≤25°C)
Стандарт	JC/T 485-2007

Подготовка поверхности — Ensure all surfaces are clean, dry and free from dust, grease and old sealant residues.
Приложение — Cut cartridge tip at 45°, load into sealant gun and apply with steady, even pressure. Tool the joint within the working time using a wet spatula.
Затвердевание — Дайте материалу отверждаться при комнатной температуре с достаточной вентиляцией. Полные механические свойства проявляются через 7 дней.
Уборка — Remove uncured sealant with a solvent. Cured sealant must be removed mechanically.

Ограничения

Не подходит для применения в несущих конструкциях.
Not recommended for movement exceeding ±20%
Not recommended for continuous water immersion or aquarium construction
Not recommended for use in fully enclosed, unventilated spaces
Not recommended for surfaces containing plasticiser or solvent residues
Не применять, если температура основания ниже 4°C или выше 40°C.

Советы

Although neutral-cure, this product uses oxime chemistry — ensure adequate ventilation during application in confined or indoor areas
For joints requiring movement capability above ±20%, consider BoPin 380 or BoPin 220
Always conduct a compatibility and adhesion test on actual project substrates before full application
Store in a cool, dry place away from direct sunlight