BoPin 820 Multi-Purpose Construction Adhesive

BoPin 820 Multi-Purpose Construction Adhesive

BoPin 820 is a single-component, moisture-curing MS polymer adhesive and sealant formulated for general construction bonding and sealing applications across a wide range of substrates. Based on modified silane polymer technology, it cures at room temperature to form a strong, flexible rubber with excellent adhesion to concrete, glass, aluminium, stainless steel, aluminium composite panel, ceramic and timber — typically without primer. The medium-hardness cured body provides a good balance of bond strength and flexibility suitable for general construction joints, panel installation and bonding applications where a versatile, paintable, solvent-free adhesive is required.

Основные преимущества

Excellent adhesion to a wide range of substrates including concrete, glass, aluminium, stainless steel, ACP, ceramic and timber — typically without primer
Paintable after cure — compatible with most water-based and solvent-based paint systems
Solvent-free, low-odour formula — suitable for use in occupied interior and exterior spaces
Good elongation (220%) — provides flexibility to accommodate minor joint movement
No shrinkage during cure
Suitable for both interior and exterior applications
Shelf life 12 months

Придерживаться

Бетон и каменная кладка
Glass and coated glass
Aluminium and aluminium alloy profiles
Stainless steel
Aluminium composite panels (ACP)
Керамика и фарфор
Timber and wood-based panels

Области применения

General construction gap and joint sealing across a wide range of substrates
Aluminium composite panel (ACP) installation and joint sealing
Interior fit-out bonding and sealing applications
Automotive body and rail vehicle body high-strength joint sealing
Elevator cab assembly and sealing

Пакет

300ml cartridge — 24 units per carton
600ml sausage pack — 20 units per carton
Available colors upon request

Детали

Система полимеризации	MS Polymer (moisture cure)
Density (g/cm³)	1.58
Твердость (по Шору A)	55
Tensile Strength (MPa)	1.56
Elongation at Break (%)	220
Skin Formation Time (min)	16
Cure Rate (depth, mm/24h)	2.0
Extrudability (g/5s)	75
Aluminium Bonding	Pass
Glass Bonding	Pass
Срок годности	Срок годности: 12 месяцев (в закрытой упаковке, при температуре ≤27°C)
Цвет	Черный, индивидуальный, серый, белый

Подготовка поверхности — Ensure all surfaces are clean, dry and free from dust, grease and loose material. For best results on smooth non-porous surfaces such as glass and polished metal, wipe with isopropyl alcohol and allow to dry before application.
Приложение — Cut cartridge tip at 45°, load into sealant gun and apply with steady, even pressure. For bonding applications, apply in parallel beads or a serpentine pattern to the bonding surface. Press components together firmly within the skin formation time.
Затвердевание — Allow to cure at room temperature with adequate ventilation. Avoid disturbing bonded components for at least 24 hours. Full mechanical properties develop after 7 days.
Cleanup — Remove uncured product with a suitable solvent before skin formation. Cured product must be removed mechanically.

Ограничения

Not suitable for PE, PP or PTFE surfaces
Не подходит для длительного погружения в воду
Не подходит для структурного остекления
Not suitable for surfaces containing plasticiser or solvent residues
Do not apply when substrate temperature is below 4°C or above 40°C

Советы

The medium hardness (Shore A 55) and good elongation (220%) make this product well suited for general construction bonding and sealing — for high-strength structural panel bonding where tensile strength above 3.0 MPa is required, consider BoPin 850
For ACP panel installation, apply adhesive beads at regular intervals across the panel back — bead spacing and pattern should be determined by panel size and wind load requirements
Paintability is a key advantage — allow full cure before applying paint for best adhesion results
Store cartridges upright in a cool, dry location away from heat and direct sunlight