BoPin 122 Silicona neutra de uso general

BoPin 122 General Purpose Neutral Silicone Sealant_benefit

BoPin 122 General Purpose Neutral Silicone_applications

BoPin 122 General Purpose Neutral Silicone_benefits

BoPin 122 Sellante de silicona neutra de uso general

BoPin 122 is a single-component, neutral-cure oxime silicone sealant suitable for a wide range of general construction sealing and bonding applications. It cures at room temperature by reacting with atmospheric moisture, releasing non-corrosive byproducts that make it safe for use on metals, coated surfaces and most common building materials. The non-sag formula maintains its position on vertical and overhead joints without slumping, and the product delivers good flexibility and durability once fully cured.

Principales ventajas

Neutral cure — non-corrosive to metals, anodised aluminium and coated surfaces
Good adhesion to most common building substrates without primer
Non-sag formula suitable for vertical and overhead joints
Good elongation (≥200%) providing reliable flexibility under minor joint movement
UV resistant — resists ageing and weathering
Rendimiento estable desde -50 °C hasta +170 °C.
Broad substrate compatibility for general construction use

Adherirse a

Vidrio y vidrio revestido
Aluminium and powder-coated metals
Ceramic and glazed tiles
Brick and concrete
Non-oily timber
Most metals (compatibility test recommended for non-standard alloys)

Áreas de aplicación

Window and door frame sealing and gap filling
Metal and aluminium alloy door and window frame to wall joint sealing
Small appliance assembly bonding and sealing
Glass, coated glass, ceramic tile, brick and concrete joint sealing
General-purpose gap filling by professional applicators

Paquete

Cartucho de 300 ml — 24 unidades por caja
600ml sausage pack — 20 units per carton
Colores disponibles bajo petición.

Información adicional

Sistema de curado	Neutral (oxime cure)
Sag / Slump	≤3 mm
Tiempo de formación de la piel	≤30 min
Working Time	≤25 min
Tasa de curado (profundidad)	1–2 mm/day
Dureza (Shore A)	40
Resistencia a la tracción	≥1.0 MPa
Alargamiento a la rotura	≥200%
Capacidad de movimiento	±15%
Resistencia a la temperatura	-50°C a +170°C
Vida útil	12 meses (sin abrir, ≤25°C)
Estándar	JC/T 485-2007

Preparación de la superficie — Ensure all surfaces are clean, dry and free from dust, grease and old sealant residues.
Aplicación — Cut cartridge tip at 45°, load into sealant gun and apply with steady, even pressure. Tool the joint within the working time using a wet spatula.
Curación — Dejar curar a temperatura ambiente con ventilación adecuada. Las propiedades mecánicas completas se desarrollan después de 7 días.
Limpieza — Remove uncured sealant with a solvent. Cured sealant must be removed mechanically.

Limitaciones

No apto para aplicaciones de carga estructural.
Not recommended for movement exceeding ±15%
Not recommended for continuous water immersion or aquarium construction
Not recommended for use in fully enclosed, unventilated spaces
Not recommended for polycarbonate or plastic sheet — compatibility test required for other plastics
Not recommended for surfaces containing plasticiser or solvent residues
No aplicar cuando la temperatura del sustrato sea inferior a 4 °C o superior a 40 °C.

Consejos

Although neutral-cure, this product uses oxime chemistry — allow adequate ventilation during application in confined areas
Always conduct a compatibility and adhesion test on actual project substrates before full application
For joints requiring movement capability above ±15%, consider BoPin 150 or BoPin 220
Store in a cool, dry place away from direct sunlight