BoPin 180 Universal Acrylic Sealant_benefit

مانع التسرب الأكريليكي العالمي BoPin 180 أكريليك 180

BoPin 180 is a single-component, water-based acrylic sealant for interior dry-area joint sealing and crack repair. It cures by water evaporation at room temperature, producing a flexible, paintable finish that blends seamlessly with surrounding surfaces. The low-odour, water-clean-up formula makes it a practical and user-friendly choice for cabinet finishing, wall crack repair, skirting board sealing and general interior decoration work where a neat, paintable result is required.

المزايا الرئيسية

Fully paintable after cure — compatible with water-based and most synthetic paints
Low odour water-based formula — safe for use in occupied interior spaces
Easy water clean-up of uncured product
Good adhesion to concrete, plaster, wood, plastic and most interior surfaces
Low stress formula — protects adjacent paint, wallpaper and delicate finishes
Very low VOC content — suitable for green building interior requirements
24-month shelf life

التزم بـ

Concrete and plaster
Wood and timber boards
Plastic and PVC profiles
Drywall and gypsum board
Ceramic tiles (dry area only)

مجالات التطبيق

Cabinet, wall panel and wallpaper edge finishing and cosmetic sealing
Interior door and window frame perimeter joint sealing
Skirting board and PU moulding edge sealing
Interior wall and ceiling crack repair

الحزمة

300ml cartridge — 24 units per carton
Available colors upon request

معلومات إضافية

نظام المعالجة	تبخر الماء
Density (g/cm³)	1.53 ± 0.03
الصلابة (شور أ)	30–50
الاستطالة عند الاستراحة	≥100%
القدرة على الحركة	± 7.5%
مقاومة درجات الحرارة	-20 درجة مئوية إلى +80 درجة مئوية
درجة حرارة التطبيق	+5 درجة مئوية إلى +40 درجة مئوية
وقت تكوين الجلد	20–30 min
قوة الشد	≥0.8 MPa
مدة الصلاحية	12 months (unopened, frost-free, ≤25°C)
اللون	مخصص
Application Fields	الإنشاءات العامة

تحضير السطح — Ensure surfaces are clean, dry and free from dust, grease and loose material. Substrate moisture content must not exceed 12%.
التطبيق — Cut cartridge tip at 45°, load into sealant gun and apply with steady, even pressure. Smooth with a wet spatula or damp finger within the working time.
المعالجة — Allow to cure at room temperature with adequate ventilation. Cure rate is 1–2mm per 24 hours. Paint only after the surface is fully dry and no longer tacky.
تنظيف — Remove uncured product with water and a damp cloth. Cured product must be removed mechanically.

القيود

Strictly not suitable for areas subject to prolonged water contact or immersion
Not suitable for structural joints
Not recommended when substrate temperature is below 5°C or above 40°C
Not recommended when ambient humidity exceeds 80% or substrate moisture content exceeds 12%
Not suitable for movement exceeding ±7.5% — for higher-movement joints use BoPin 630
غير مناسب للوصلات الخارجية مع التعرض المباشر للعوامل الجوية

الإرشادات

For best paintability, allow full cure before applying paint — painting too early may cause cracking
Slightly moisten very porous substrates (plaster, brick) before application to improve adhesion
Product must be protected from freezing during storage and transport
Store cartridges upright in a cool, dry location away from heat sources