مانع تسرب السيليكون السيليكون BoPin 635 من الحجر الطبيعي

BoPin 635 Natural Stone Silicone Sealant_600ml

BoPin 635 Natural Stone Silicone Sealant_benefit

مانع تسرب السيليكون السيليكون BoPin 635 من الحجر الطبيعي

BoPin 635 is a single-component, neutral-cure silicone sealant from our premium certified natural stone silicone series, specifically formulated for natural stone sealing applications. The non-staining neutral cure system ensures no oil migration into porous stone surfaces such as marble, granite, limestone and travertine — a critical requirement that standard neutral-cure silicones cannot always guarantee. The product bonds reliably to natural stone, glass, ceramic tile, aluminium and coated metals without primer, and delivers durable flexibility with good movement capability to accommodate the thermal expansion and structural movement characteristic of stone installations. Suitable for both interior and exterior stone sealing applications.

المزايا الرئيسية

Non-staining formula — prevents oil migration and edge discolouration on porous natural stone surfaces
Safe for all natural stone types including marble, granite, limestone and travertine
Good adhesion to natural stone, glass, ceramic and aluminium without primer
Good movement capability — accommodates thermal expansion and structural movement in stone installations
UV resistant — stable colour and performance in exterior stone applications
Suitable for wet-area stone applications — compatibility with stone sealers recommended

التزم بـ

Marble, granite, limestone and travertine
Engineered stone and composite stone panels
بلاط السيراميك والبورسلين
Glass and coated glass
Aluminium and anodised aluminium
الخرسانة والبناء

مجالات التطبيق

Marble and granite countertop and worktop joint sealing
Natural stone floor joint sealing
Stone curtain wall and facade panel joint sealing
Shower enclosure and wet-area natural stone sealing
Decorative stone panel installation joint sealing

الحزمة

300ml cartridge — 24 units per carton
600ml sausage pack — 20 units per carton
Available colors upon request

معلومات إضافية

نظام المعالجة	Neutral cure
Sag / Slump	≤3 mm
مقاومة درجات الحرارة	-50°C to +170°C
مدة الصلاحية	12 months (unopened, ≤25°C)
معيار	GB/T 14683-2017

تحضير السطح — Ensure all stone surfaces are clean, dry and free from dust, grease, stone sealers and old sealant residues. Remove any existing stone sealer from the joint area as this may affect adhesion. Do not wet the stone before application.
التطبيق — Cut cartridge tip at 45°, load into sealant gun and apply with steady, even pressure into the joint. Tool immediately using a spatula dampened with soapy water. Apply masking tape for clean joint lines on polished stone.
المعالجة — Allow to cure at room temperature with adequate ventilation. Avoid water contact for at least 24 hours. Full mechanical properties develop after 7 days.
تنظيف — Remove uncured sealant with a solvent before skin formation. Cured sealant must be removed mechanically — take care not to scratch polished stone surfaces.

القيود

Not suitable for structural glazing or primary load-bearing applications
Not suitable for continuous full water immersion
Not suitable for use in fully enclosed, unventilated spaces
Not suitable for surfaces containing plasticiser or solvent residues
Not suitable for PE, PP or PTFE surfaces
Do not apply when substrate temperature is below 4°C or above 40°C

الإرشادات

Always conduct an adhesion and staining test on actual stone samples before full project application — stone porosity and surface treatment vary significantly between stone types and sources
For polished stone surfaces, apply masking tape carefully along both sides of the joint before application to protect the polished finish — remove immediately after tooling
If the stone has been previously sealed with a penetrating stone sealer, the sealer must be removed from the joint bonding surfaces before applying sealant
Store cartridges upright in a cool, dry location away from heat and direct sunlight