BoPin 240 Economy Standard Foam

BoPin 240 is a single-component, moisture-curing polyurethane expanding foam sealant in a 750ml aerosol can. It expands on contact with atmospheric moisture to fill gaps and voids, curing into a rigid, closed-cell foam with excellent thermal insulation, acoustic damping and moisture resistance properties. The standard-expansion formula is well suited to general construction gap filling, door frame installation, pipe penetration sealing and building maintenance work where precise low-pressure application is not required. Its economy positioning makes it an accessible choice for contractors and maintenance teams working on general projects.

Principaux avantages

Self-expanding formula fills irregular gaps and voids completely
Excellent thermal insulation — λ = 0.038 W/m·K
Good acoustic damping — reduces sound transmission through filled gaps
Moisture resistant after full cure — closed-cell structure resists water ingress
Adheres to most common building substrates without primer
Trimmable after full cure
B3 fire classification

Adhere To

Béton et maçonnerie
Brick and blockwork
Timber and wood-based boards
Metal frames and profiles
Most plastics (test recommended on polystyrene and polycarbonate)

Application Areas

General construction gap and void filling
Door frame and interior frame installation
Pipe and cable penetration sealing through walls
Building maintenance crack and gap repair
Warehouse and industrial building gap filling
Thermal and acoustic insulation of partition walls

Paquet

750ml aerosol can — 12 cans per carton Available colors: Off-white / cream (foam colour as cured)

Informations complémentaires

Système de polymérisation	Moisture cure (single component)
Foam Structure	Closed-cell elastic foam
Thermal Conductivity (λ)	0.038 W/m·K
Fire Classification	B3
Température d'application	+5°C to +35°C (optimum +18°C to +25°C)
Temperature Resistance (cured)	De -30°C à +80°C
Tack-Free Time	8–15 min (23°C / 50% RH)
Full Cure Time	12–24 hours
Trimming Time	30–60 min
Durée de conservation	12 months (unopened, ≤27°C)
Couleur	Customized
Standard	JC/T 936-2004

Preparation — Shake can vigorously for 30 seconds before use. Lightly dampen the substrate with water to accelerate cure. Ensure adequate ventilation.
Application — Attach applicator straw or foam gun. Hold can inverted and apply foam to fill approximately 50% of the gap — foam will expand to fill the remainder. Work from the back of the gap towards the front.
Curing — Allow to cure fully before trimming. Tack-free in 8–15 minutes. Trim excess foam with a sharp knife after 30–60 minutes. Full cure in 12–24 hours.
Finishing — Cured foam can be painted or plastered over after full cure.

Limitations

Must be applied in well-ventilated areas — wear protective gloves and safety glasses during application
Do not use near open flames or ignition sources — contents are flammable before cure
Do not use on polystyrene foam insulation boards — foam solvents may cause damage
Cured foam is strongly alkaline — avoid contact with clothing during application
Do not store cans inverted or on their side
Do not incinerate or puncture used cans
Not suitable for fire-rated penetration sealing — use BoPin 730 for fire-rated applications
Not suitable for movement joints or structural applications
Standard expansion formula not recommended for sensitive aluminium window frames — use BoPin 270 Low-Expansion Foam instead

Conseils

For best yield, warm the can to 20–25°C before use — cold cans produce less foam output
Partially used cans can be stored with the straw attached if the valve is kept clean — use within a short period after opening
Foam expands significantly — apply conservatively and allow expansion before adding more
UV exposure will cause yellowing and surface degradation of uncovered foam — always cover with paint, plaster or sealant in exposed locations

BoPin 240 Economy Standard Foam

Informations complémentaires

Similar and Related Products

Produits similaires

BoPin 150 All-Weather Construction Silicone Sealant

BoPin 635 Scellant silicone pour pierres naturelles

BoPin 380, mastic de façade résistant aux intempéries

BoPin 550 Joint silicone neutre sanitaire