BoPin 1010 Selante para Pré-fabricados e Construções Sustentáveis

BoPin 1010 Prefab & Green Building Sealant_600ml

BoPin 1010 Prefab & Green Building Sealant_benefit

BoPin 1010 Selante para Pré-fabricados e Construções Sustentáveis

BoPin 1010 is a single-component, moisture-curing MS polymer sealant specifically formulated for prefabricated building joint sealing and general construction bonding and sealing applications. Based on modified silane polymer technology, it cures at room temperature to form an exceptionally soft, highly elastic rubber with outstanding elongation of 515% — one of the highest in the MS polymer range. The very low Shore A hardness of 22 makes it particularly well suited to large panel-to-panel joints in prefabricated and modular construction systems, where differential structural movement between building elements demands a sealant that absorbs displacement without transmitting stress to the substrate. Zero sag ensures reliable application on vertical facade joints without movement or slumping. Also suitable for general construction bonding of concrete, stone, glass, aluminium and timber.

Principais benefícios

Exceptional elongation — 515% at break, accommodates large differential movement between prefabricated building elements
Very soft cured body — Shore A hardness 22, absorbs joint movement without stress transfer to substrate or panel edges
Zero sag — maintains position on vertical facade joints without slumping
Good adhesion to concrete, stone, glass, aluminium and timber — typically without primer
Solvent-free, low-odour formula — suitable for use in occupied building environments
Adequado para aplicações internas e externas.
Validade: 12 meses

Aderir a

Betão e alvenaria
Natural stone and engineered stone panels
Vidro e vidro revestido
Perfis de alumínio e liga de alumínio
Painéis de madeira e derivados
Most common building substrate combinations

Áreas de aplicação

Prefabricated building interior and exterior wall panel joint sealing
Urban utility tunnel and underground structure joint sealing
Interior fit-out joint sealing and gap filling
General construction material bonding and sealing — concrete, stone, glass, aluminium, timber
Modular building and off-site construction assembly joint sealing
Solvent-free joint sealing for interior and exterior building applications

Embalagem

Cartucho de 300 ml — 24 unidades por caixa
Pacote de salsichas de 600ml — 20 unidades por caixa
Cores disponíveis mediante solicitação.

Informação adicional

Sistema de cura	Polímero MS (cura por umidade)
Densidade (g/cm³)	1.35
Dureza (Shore A)	22
Resistência à tração (MPa)	0.95
Alongamento na ruptura (%)	515
Sag / Slump (mm)	0
Tempo de formação da pele (min)	35
Taxa de cura (profundidade, mm/24h)	1.8
Consistency (g/5s)	120
Bonding	Passar
Prazo de validade	12 meses (fechado, ≤27°C)
Cor	Preto, Personalizado, Cinzento, Branco

Preparação da superfície — Ensure all surfaces are clean, dry and free from dust, grease, old sealant residues and loose material. For concrete and masonry surfaces, remove any laitance or loose particles by mechanical means.
Aplicação — Cut cartridge tip at 45°, load into sealant gun and apply with steady, even pressure into the joint. Tool within the working time using a spatula dampened with soapy water. Apply masking tape for clean joint lines on finished surfaces.
Cura — Deixe curar à temperatura ambiente com ventilação adequada. As propriedades mecânicas completas se desenvolvem após 7 dias.
Limpar — Remova o produto não curado com um solvente adequado antes da formação de película. O produto curado deve ser removido mecanicamente.

Limitações

Não é adequado para aplicações estruturais de suporte de carga.
Não recomendado para imersão contínua em água
Não é adequado para superfícies de PE, PP ou PTFE.
Não é adequado para superfícies que contenham resíduos de plastificantes ou solventes.
Não aplicar quando a temperatura do substrato estiver abaixo de 4°C ou acima de 40°C.

Dicas

The very low Shore A hardness (22) means this product has lower tensile strength (0.95 MPa) than harder MS grades — it is designed for high-movement joint sealing, not high-load structural bonding; for structural panel bonding use BoPin 850
The zero-sag formula performs well on vertical facade joints — no backing rod support required for shallow joints
In prefabricated building applications, ensure joint width is designed to accommodate the full anticipated differential movement between panels — joint width should be calculated based on panel dimensions and thermal movement coefficients
Always conduct a compatibility and adhesion test on actual project substrate combinations before full application
Armazene os cartuchos na vertical, em local fresco e seco, longe do calor e da luz solar direta.