BoPin 640 Decorative Trim Silicone Sealant_benefit

Sellador de silicona para molduras decorativas BoPin 640

BoPin 640 is a single-component, neutral-cure, high-strength silicone sealant formulated for interior decorative finishing and trim sealing applications. It combines good elasticity with waterproof and moisture-resistant properties, making it suitable for securing and sealing decorative elements including door and window surrounds, skirting boards, cabinet bodies and toilet bases. The green-certified, eco-friendly formula carries very low odour and is suitable for use in occupied residential and commercial interiors. Multiple colour options allow the product to blend with surrounding decorative finishes for a clean, professional result.

Principales ventajas

Neutral cure — non-corrosive, safe for use on all common interior decorative materials
High bond strength and elasticity — secures decorative trim elements while accommodating minor movement
Waterproof seal — prevents moisture and water ingress at decorative joints
Seals joints against moisture, pest ingress and harmful gas infiltration
Prevents wallpaper edge lifting and blocks dust infiltration at wall junctions
Green-certified eco-friendly formula — low odour, suitable for occupied interior spaces
Multiple colour options — blends with surrounding decorative finishes
Easy to clean joint surfaces

Adherirse a

Wood and timber-based mouldings and profiles
PVC and painted profiles
Painted concrete and plaster walls
Most common interior decorative trim substrates

Áreas de aplicación

Door surround and window surround securing and sealing
Skirting board and PU moulding edge fixing and sealing
Cabinet body installation and perimeter joint sealing
Toilet base and bathroom fixture perimeter sealing
Preventing wallpaper edge lifting at wall junctions
General interior decorative joint finishing and cosmetic sealing

Paquete

Cartucho de 300 ml — 24 unidades por caja
600ml sausage pack — 20 units per carton
Colores disponibles bajo petición.

Información adicional

Sistema de curado	Curado neutro
Sag / Slump	≤3 mm
Tiempo de formación de la piel	≤20 min
Working Time	≤20 min
Tasa de curado (profundidad)	2–4 mm/day
Dureza (Shore A)	40
Resistencia a la tracción	≥1.0 MPa
Alargamiento a la rotura	≥200%
Vida útil	12 months (unopened, ≤27°C)
Color	Negro, Personalizado, Gris, Blanco
Estándar	JC/T 485-2007

Preparación de la superficie — Ensure all surfaces are clean, dry and free from dust, grease and old sealant residues. Surfaces must be fully dry before application.
Aplicación — Cut cartridge tip at 45°, load into sealant gun and apply with steady, even pressure. Tool within the working time using a wet spatula for a smooth finish. Apply masking tape along both sides of the joint for clean, precise lines.
Curación — Dejar curar a temperatura ambiente con ventilación adecuada. Las propiedades mecánicas completas se desarrollan después de 7 días.
Limpieza — Retire el sellador sin curar con un disolvente antes de que se forme la capa superficial. El sellador curado debe retirarse mecánicamente.

Limitaciones

No apto para inmersión continua en agua
No apto para aplicaciones de carga estructural.
Keep away from children
Ensure adequate ventilation during and after application
No aplicar cuando la temperatura del sustrato sea inferior a 4 °C o superior a 40 °C.
Do not store above 27°C

Consejos

Apply masking tape along both sides of the joint before application for clean, professional lines — remove immediately after tooling before skin forms
For toilet base sealing, ensure the base and floor are completely dry and clean before applying — any residual cleaning product or moisture will shorten joint service life
In high-humidity climates, allow adequate ventilation after application to ensure full cure
Guarde los cartuchos en posición vertical en un lugar fresco y seco, alejado del calor y la luz solar directa.